Wir versenden mit

 

Wir akzeptieren

 
 

Kontakt: AM Speed Parts

AM Speed Parts für US-Cars

American Speed 'n' Classics UG

Schacht Neu-Cöln 26
45355 Essen
Tel.: 0201 / 3619365
Fax: 0201 / 3619176

Shop: www.am-speed.de
 
TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump
Alle Artikel zeigen aus: Fuel Line Kits
 
Artikelnr.: stro9141-7RA
 
99,95 EUR
inkl. 19,00% MwSt. zzgl. Versand
Versandfertig: 72 Stunden
 
TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump
 
 
TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump  
  99,95 EUR *  
 Stk. 
* inkl. 19,00% MwSt. zzgl. Versand
 
TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump
  • Fits Offenhauser 1075 (1949-53) intake manifold
  • Use with Ford 7RA-9350 fuel pump
  • Simple Two Step installation
  • Accurate CNC-bent 1/4inch OD lines
  • Furnace brazed joints for OE looks and quality
  • All stainless steel construction with unique tapered T-piece
Stainless steel fuel line for use on Offenhauser 1075 (1949-53 Ford Flathead) intake with 7RA '8BA engine' fuel pump and mount.

Designed and manufactured exclusively by Stromberg Carburetor, TwoStep Fuel Lines combine super-clean looks with hot rod styling and simple installation. Each kit is supplied ready to install in just two simple steps.
TwoStep kits are not a ‘one size fits all’ solution. They're CAD engineered to fit Stromberg 97, 81, 48 and 40 carburetors on specific intake manifolds with specific fuel pumps (or a remote pump), so please check you're ordering the right kit. Carburetor spacing differs between intake makes and models and fuel pump mounts vary.

This fuel line fits two carburetors on the Offenhauser 1075 intake (for 1949-53 Ford Flathead engines) with the stock Ford-type 7RA-9350 fuel pump. This pump is available new from your favourite Early Ford parts Shop - try our dealers first!. It DOES NOT fit the 1951-53 Ford 1BA-9350 fuel pump which requires 1/8in NPT fittings.

Check out the following features:
  • 1/4inch OD lines, CAD-designed and CNC-bent for an exact fit.

  • Invisible furnace brazed joints for OE looks and fuel-tight quality.

  • All stainless steel construction.

  • Brass Ford Nut fittings are supplied.
Every Stromberg TwoStep Fuel Line kit comes with full instructions, and further help with selection, installation and tuning is available at our Tech Center.

Please note: The TwoStep fuel line is simple to fit, but on some intake manifolds, you may need to rotate the top of the fuel pump to get the optimum line from carbs to pump outlet. This is a typical Hot Rod trick and very easy to do. Simply remove the small screws around the top of the pump, keeping downward pressure on the top before releasing the spring gently. Rotate the top casting (usually by one screw space) and replace the screws tight.

One more thing. Unlike some aftermarket needle & seat inlet fittings, Genuine Stromberg S-jets ensure that the fuel line fits the same depth into each carburetor, which is vital for good fuel line alignment. All new Genuine Stromberg 97 carburetors are S-jet equipped.